to Flare. CLF crew used a TVA-1000 to sample the area of migration on the west side of CLF. Hot spots were found in new areas and were coned off to keep people away. Greased blowers and exercised valves at Flare. Took monthly readings of flow meter Collected data on CLF and RR1. Greased blowers and exercised valves at Flare. Took monthly readings of flow meter. 2016 Work and Activity Performed August 5, 2016 • August 8, 2016 • August 17-19, 2016 • • August 23-26, 2016 September 2, 2016 • • September 7, 2016 • • • September 14-16, 2016 October 7, 2016 October 13, 2016 October 14, 2016 • • • • • October 24-27, 2016 November 1, 2016 • • November 2, 2016 • • • • • November 14-18 2016 November 22, 2016 December 3, 2016 December 4, 2016 • • • • • CLF crew along with Cornerstone continued investigating gas migration area. While on site Cornerstone replaced EW-13A valve with fine tune valve to help slow the flow of the well. Hopefully this will give the CLF crew a steady flow of gas. CLF crew took bar tests along edge of liner near the gas migration area. Some gas was found south of EW-13A. CLF crew sounded all gas wells on the North header. Flare shut down at 2:30pm due to power outage. We monitored the restart of the flare at 7:15am the next morning. CLF crew collected data on CLF and RR1. Joe from Landtech came to train the CLF crew on the new GEM 5000. CLF crew used a TVA-1000 to conducted surface sampling in the area of EW-13A. After surface samples were taken they then bar tested the "hot spots" with their GEM 2000. Greased blowers and exercised valves at Flare. Took monthly readings of flow meter. CLF crew collected data on CLF and RR1. Greased blowers and exercised valves at Flare. Took monthly readings of flow meter. CLF crew greased storm water gate at bulkhead. CLF crew used the NA-1000 to surface sample EW-54, EW-88, EW-96, EW-60, and EW-74. They also checked known "hot spots" in area of gas migration. CLF crew collected data on CLF and RR1. Flare was down at 8:00am for maintenance. Flare was restarted and monitored at 11:00am. Greased blowers and exercised valves at Flare. Took monthly readings of flow meter. Collected data on CLF and RR1. Removed water from vaults on RR1. Flare shut down at 12:00pm due to power outage. We monitored the restart of the flare at 12:30 pm. Greased blowers and exercised valves at Flare. Took monthly readings of flow meter. Tightened all valves and fittings at the Flare. Drained water from header at EW-73. Shut Flare down at 8:30am so we could change the #2 thermal sensor. Flare was restarted and monitored at 10:00am. 2016 Work and Activity Performed December 14, 2016 • • December 12-16, 2016 • • CLF crew plotted a grid in the area of EW-13A. They then began to take bar samples in the area to evaluate if the horizontal well was helping. At this time there were still high levels of CH4. CLF crew had meeting with the Parks department to discuss remapping of bio-diversity zones. We were only there to aide Parks with information of CLF and RR1. Collected data on CLF and RR1. Removed water from vaults on RR1. 2017 Work and Activity Performed January 4, 2017 January 11, 2017 • • • January 12, 2017 January 20, 2017 • • • February 12, 2017 February 19-23, 2017 February 24 and 27, 2017 March 3, 2017 March 9, 2017 March 20-24, 2017 • • • • • • • April 13-14, 2017 • • • • April 17, 2017 • April 19, 2017 April 20, 2017 • • • • April 24-27, 2017 May 2, 2017 • • May 5, 2017 • • • May 9, 2017 • Greased blowers and exercised valves at Flare. Took monthly readings of flow meter. CLF crew turned Flare off at 8:30 am, then raised the PID to 55.0 to draw water in lines to condensation pump. Restarted the Flare and returned the PID to -9.0 at 9:30 am. CLF crew changed well heads at EW-69 and EW-92. CLF crew had meeting with Mario and Lou about migrating gas and the work that had been done to correct the problem. During this time the Pump Station project was still active and another bypass was created at Pump Station 1. We proceeded to monitor the bypass daily to prevent another spill. Greased blowers and exercised valves at Flare. Took monthly readings of flow meter. Collected data on CLF and RR1. CLF crew removed woodys from flare area and around CLF. Greased blowers and exercised valves at Flare. Took monthly